Quiz Questions

Question 1 1 Marks

Which one is the properties of lubricant

A

Boiling temperature should be low

B

Should develop foam

C

Oil viscosity should not be same in hot and cold condition

D

Oil viscosity should be suit the operating conditions

Question 2 1 Marks

Which part drives the oil pump?

A

Crank Shaft

B

Cam Shaft

C

Crank pulley

D

Timing gears

Question 3 1 Marks

Which part is lubricated by splash lubrication system?

A

Timing gears

B

Main journal

C

Crank pin

D

Cylinder wall

Question 4 1 Marks

How oil deliver from the crank shaft main bearings to connecting rod bearings?

A

Through drilled oil passages

B

Through crank pulley

C

Through sprocket

D

Through vibration damper

Question 5 1 Marks

What is the purpose of a radiator pressure cap?

A

Release the excess pressure

B

Maintain the water temperature

C

Retain the vacuum pressure

D

Retain the atmospheric pressure

Question 6 1 Marks

What is the purpose of water pump in cooling system?

A

Force the water circulation

B

Reduce the water pressure

C

Increase the water temperature

D

Flushing out the cooling system

Question 7 1 Marks

Which part is used to pump the water in water pump?

A

Bearing

B

Shaft

C

Pulley

D

Impeller

Question 8 1 Marks

What is the effect if thermostat valve is struck?

A

Engine gets over cooling

B

Engine gets over heating

C

Engine does not start

D

Engine does not stop

Question 9 1 Marks

Where heat dissipation take place in cooling system?

A

Radiator

B

Water pump

C

Water jackets

D

Fan

Question 10 1 Marks

Which type of pump is used in water cooling system?

A

Gear pump

B

Diaphragm pump

C

Centrifugal pump

D

Reciprocating pump

Question 11 1 Marks

How many valves are used in radiator cap?

A

One valve

B

Two valves

C

Three valves

D

Four valves

Question 12 1 Marks

Which part allows to flow water from upper tank to lower tank of the radiator?

A

Fins

B

Core tubes

C

Water pump

D

Bottom hole

Question 13 1 Marks

What is the purpose of the radiator in the cooling system?

A

Cool the hot air

B

Cool the hot oil

C

Cool the hot water

D

Cool the water pump

Question 14 1 Marks

What is the purpose of metal fins in air cooling system?

A

Supply the heat

B

Increase the heat

C

Reduce the heat

D

Maintain the heat

Question 15 1 Marks

Where the metal fins are provided in the air cooled engine?

A

Cylinder and head

B

Exhaust pipe

C

Valve door

D

Intake manifold

Question 16 1 Marks

Which types of cooling system the rate of cooling is very low?

A

Thermo siphon system

B

Air cooling system

C

Forced feed system

D

Pump circulation system

Question 17 1 Marks

How the water pump get drive in pump circulation cooling system?

A

By belt

B

By gear

C

By chain

D

By coupling

Question 18 1 Marks

Which mixture is used in radiator reverse flushing cleaning?

A

Flushing water with air (gun) pressure

B

Flushing water with engine oil

C

Flushing water with coolant oil

D

Flushing water with soap oil

Question 19 1 Marks

When the thermostat valve open in engine?

A

Low temperature of engine

B

High temperature of engine

C

Operating temperature of engine

D

Freezing temperature of engine

Question 20 1 Marks

What is the material used to produce crank shaft?

A

Chromium vanadium nickel steel

B

High speed steel

C

Cast iron

D

Wrought iron

Question 21 1 Marks

What is the material of piston pins?

A

Nickel chromium steel

B

Cast iron

C

HSS

D

Bronze

Question 22 1 Marks

What is the name the portion below the piston boss?

A

Land of the piston

B

Ring section of the piston

C

Crown of the piston

D

Skirt of the piston

Question 23 1 Marks

What type of bearing fitted in the connecting rod big end?

A

Needle bearing

B

Ball bearing

C

Taper roller bearing

D

Shell bearing

Question 24 1 Marks

Which part connect the piston with connecting rod?

A

Piston pin

B

Spilt pin

C

Crank pin

D

Cotter pin

Question 25 1 Marks

Which part is connect the piston with crank pin?

A

Push rod

B

Connecting rod

C

Cam Shaft

D

Crank Shaft

Question 26 1 Marks

Which tool used to remove the crank shaft pully?

A

Double and spanner

B

Ring spanner

C

Pipe wrench

D

Puller

Question 27 1 Marks

Which tool is used to measure the diameter of the crank shaft main journal?

A

Inside micrometer

B

Outside micrometer

C

Three point internal micrometer

D

Master ring gauge

Question 28 1 Marks

What is the material for cam shaft?

A

Forged alloy steel

B

Copper alloy

C

Aluminium alloy

D

Zinc alloy

Question 29 1 Marks

Which tool is required to remove the valves?

A

Torque wrench

B

Valve spring lifter

C

Box spanner

D

Scraper

Question 30 1 Marks

Which instrument is used to check the vacuum of the cylinder?

A

Compression gauge

B

Dial gauge

C

Vacuum gauge

D

Wire gauge

Question 31 1 Marks

Which measuring instrument used to check the fly wheel face out?

A

Dial indicator

B

Compression gauge

C

Outside micrometer

D

Feeler gauge

Question 32 1 Marks

Which is the most preferred use of taper roller bearings?

A

Gear boxes

B

Fly wheel and water pump

C

Differential and wheel hub

D

Connecting rods

Question 33 1 Marks

What is the property of a bearing helps to with stand metal to metal contact?

A

Surface action

B

Thermal conductivity

C

Fatique strength

D

Embeddability

Question 34 1 Marks

Which is the most preferred use of roller bearings?

A

Gear boxes

B

Fly wheel

C

Differential

D

Connecting rods

Question 35 1 Marks

Which is connected with pison through piston pin?

A

Gudgeon pin

B

Connecting rod

C

Cam shaft

D

Rocker arm

Question 36 1 Marks

Which is the key element in converting reciprocating motion in to rotary motion?

A

Connecting rod

B

Gudgeon pin

C

King pin

D

Cam shaft

Question 37 1 Marks

Which is transferring energy for the piston to crankshaft?

A

Gudgeon pin

B

King pin

C

Connecting rod

D

Cam shaft

Question 38 1 Marks

Which is the load taken by the roller bearing?

A

Radial load

B

Axial load

C

Thrust load

D

Radial and axial load

Question 39 1 Marks

1). Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Try square | ಟ್ರೈ ಸ್ಕ್ವೇರ್

B

Surface gauge | ಮೇಲ್ಮೈ ಮಾಪಕ

C

Steel rule | ಸ್ಟೀಲ್ ರೂಲ್

D

Feeler gauge | ಫೀಲರ್ ಗೇಜ್

Question 40 1 Marks

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

A

Lead | ಲೀಡ್

B

Glass | ಗಾಜು

C

Wood | ಮರ

D

Paper | ಪೇಪರ್

Question 41 1 Marks

Identify the name of the triangle? | ತ್ರಿಕೋನದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Equilateral triangle | ಸಮಕೋನ ತ್ರಿಕೋನ

B

Isosceles triangle | ಸಮದ್ವಿಬಾಹು ತ್ರಿಭುಜ

C

Scalene triangle | ಸ್ಕೇಲಿನ್ ತ್ರಿಕೋನ

D

Right angle triangle | ಬಲ ಕೋನ ತ್ರಿಕೋನ

Question 42 1 Marks

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Ball pein hammer | ಬಾಲ್ ಪೆನ್ ಸುತ್ತಿಗೆ

B

Mallet | ಮ್ಯಾಲೆಟ್

C

Cross pein hammer | ಕ್ರಾಸ್ ಪೀನ್ ಸುತ್ತಿಗೆ

D

Straight pein hammer | ಸ್ಟ್ರೈಟ್ ಪೆಯಿನ್ ಸುತ್ತಿಗೆ

Question 43 1 Marks

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

A

Steel | ಸ್ಟೀಲ್

B

Wood | ಮರ

C

Glass | ಗಾಜು

D

Concrete | ಕಾಂಕ್ರೀಟ್

Question 44 1 Marks

Identify the correct aligned system dimension? | ಸರಿಯಾದ ಜೋಡಿಸಲಾದ ಸಿಸ್ಟಮ್ ಆಯಾಮವನ್ನು ಗುರುತಿಸುವುದೇ?

A

B

C

D

Question 45 1 Marks

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

A

Concrete | ಕಾಂಕ್ರೀಟ್

B

Steel | ಸ್ಟೀಲ್

C

Wood | ಮರ

D

Glass | ಗಾಜು

Question 46 1 Marks

Which single stroke inclined letter ʹAʹ is correct as per IS standard? | IS ಮಾನದಂಡದ ಪ್ರಕಾರ ಯಾವ ಏಕ ಸ್ಟ್ರೋಕ್ ಇಳಿಜಾರಿನ ಅಕ್ಷರ ʹAʹ ಸರಿಯಾಗಿದೆ?

A

B

C

D

Question 47 1 Marks

Which arrow head is correct as per standard? | ಮಾನದಂಡದ ಪ್ರಕಾರ ಯಾವ ಬಾಣದ ಹೆಡ್ ಸರಿಯಾಗಿದೆ?

A

B

C

D

Question 48 1 Marks

Which dimension correctly marked in the circle as per standard? | ಮಾನದಂಡದ ಪ್ರಕಾರ ವೃತ್ತದಲ್ಲಿ ಯಾವ ಆಯಾಮವನ್ನು ಸರಿಯಾಗಿ ಗುರುತಿಸಲಾಗಿದೆ?

A

B

C

D

Question 49 1 Marks

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

A

Water | ನೀರು

B

Concrete | ಕಾಂಕ್ರೀಟ್

C

Asbestos | ಆಸ್ಬೆಸ್ಟೋಸ್

D

Glass | ಗಾಜು

Question 50 1 Marks

Identify the name of instrument? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Set square | ಸೆಟ್ ಸ್ಕ್ವೇರ್

B

Protractor | ಪ್ರೊಟ್ರಾಕ್ಟರ್

C

French curve | ಫ್ರೆಂಚ್ ಕರ್ವ್

D

ʹ T ʹ square | ʹಟಿʹ ಸ್ಕ್ವೇರ್

Question 51 1 Marks

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Hawk-billed shear | ಹಾಕ್-ಬಿಲ್ಡ್ ಷಿಯರ್

B

Aviation shear | ಏವಿಯೇಷನ್ ಷಿಯರ್

C

Cutting plier | ಕಟಿಂಗ್ ಪ್ಲೈಯರ್

D

Double cutting shear | ಡಬಲ್ ಕಟಿಂಗ್ ಷಿಯರ್

Question 52 1 Marks

Which drawing dimension is correct as per IS standard? | IS ಮಾನದಂಡದ ಪ್ರಕಾರ ಯಾವ ರೇಖಾಚಿತ್ರದ ಆಯಾಮವು ಸರಿಯಾಗಿದೆ?

A

B

C

D

Question 53 1 Marks

Identify the line ʹbʹ? | ʹbʹ ಸಾಲನ್ನು ಗುರುತಿಸುವುದೇ?

A

Dimension line | ಡೈಮೆನ್ಶನ್ ಲೈನ್

B

Extension line | ಎಕ್ಸಟೆನ್ಶನ್ ಲೈನ್

C

Leader line | ಲೀಡರ್ ಲೈನ್

D

Termination of dimension line | ಆಯಾಮ ರೇಖೆಯ ಮುಕ್ತಾಯ

Question 54 1 Marks

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Ball pein hammer | ಬಾಲ್ ಪೆನ್ ಸುತ್ತಿಗೆ

B

Cross pein hammer | ಕ್ರಾಸ್ ಪೀನ್ ಸುತ್ತಿಗೆ

C

Straight pein hammer | ನೇರ ಪೆನ್ ಸುತ್ತಿಗೆ

D

Sledge hammer | ಸ್ಲೆಡ್ಜ್ ಸುತ್ತಿಗೆ

Question 55 1 Marks

Identify the name of prism? | ಪ್ರಿಸ್ಮ್ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Square prism | ಚದರ ಪ್ರಿಸ್ಮ್

B

Pentagonal prism | ಪೆಂಟಗೋನಲ್ ಪ್ರಿಸ್ಮ್

C

Triangular prism | ತ್ರಿಕೋನ ಪ್ರಿಸ್ಮ್

D

Hexagonal prism | ಷಡ್ಭುಜೀಯ ಪ್ರಿಸ್ಮ್

Question 56 1 Marks

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Open end spanner | ಓಪನ್ ಎಂಡ್ ಸ್ಪ್ಯಾನರ್

B

Ring spanner | ರಿಂಗ್ ಸ್ಪ್ಯಾನರ್

C

Combination spanner | ಕಾಂಬಿನೇಶನ್ ಸ್ಪ್ಯಾನರ್

D

Adjustable spanner | ಹೊಂದಿಸಬಹುದಾದ ಸ್ಪ್ಯಾನರ್

Question 57 1 Marks

What is the trimmed size of A4 sheet? | A4 ಹಾಳೆಯ ಟ್ರಿಮ್ ಮಾಡಿದ ಗಾತ್ರ ಎಷ್ಟು?

A

841 x 1189

B

594 x 841

C

210 x 297

D

148 x 210

Question 58 1 Marks

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

A

Lead | ಲೀಡ್

B

Steel | ಸ್ಟೀಲ್

C

Glass | ಗಾಜು

D

Porcelain | ಪಿಂಗಾಣಿ

Question 59 1 Marks

Which drawing dimension is correct as per standard drawing practice? | ಸ್ಟ್ಯಾಂಡರ್ಡ್ ಡ್ರಾಯಿಂಗ್ ಅಭ್ಯಾಸದ ಪ್ರಕಾರ ಯಾವ ಡ್ರಾಯಿಂಗ್ ಆಯಾಮ ಸರಿಯಾಗಿದೆ?

A

B

C

D

Question 60 1 Marks

Which title block position is correct as standard practice? | ಪ್ರಮಾಣಿತ ಅಭ್ಯಾಸದಂತೆ ಯಾವ ಶೀರ್ಷಿಕೆ ಬ್ಲಾಕ್ ಸ್ಥಾನವು ಸರಿಯಾಗಿದೆ?

A

B

C

D

Question 61 1 Marks

Identify the name of prism? | ಪ್ರಿಸ್ಮ್ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

Rectangle prism | ಆಯತ ಪ್ರಿಸ್ಮ್

B

Square prism | ಚದರ ಪ್ರಿಸ್ಮ್

C

Triangular prism | ತ್ರಿಕೋನ ಪ್ರಿಸ್ಮ್

D

Hexagonal prism | ಷಡ್ಭುಜೀಯ ಪ್ರಿಸ್ಮ್

Question 62 1 Marks

Compass used to draw for_. | ಕಂಪಾಸ್ ಅನ್ನು _ ಗೆ ಸೆಳೆಯಲು ಬಳಸಲಾಗುತ್ತದೆ.

A

rectangle | ಆಯಾತ

B

square | ಚದರ

C

circle | ವೃತ್ತ

D

triangle | ತ್ರಿಕೋನ

Question 63 1 Marks

Identify the name of set square? | ಸೆಟ್ ಚೌಕದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

15° set square | 15° ಸೆಟ್ ಸ್ಕ್ವೇರ್

B

60° set square | 60° ಸೆಟ್ ಸ್ಕ್ವೇರ್

C

30°set square | 30° ಸೆಟ್ ಸ್ಕ್ವೇರ್

D

45°set square | 45° ಸೆಟ್ ಸ್ಕ್ವೇರ್

Question 64 1 Marks

Identify the name of set square? | ಸೆಟ್ ಚೌಕದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

A

15° set square | 15° ಸೆಟ್ ಸ್ಕ್ವೇರ್

B

60° set square | 60° ಸೆಟ್ ಸ್ಕ್ವೇರ್

C

30°set square | 30° ಸೆಟ್ ಸ್ಕ್ವೇರ್

D

45°set square | 45° ಸೆಟ್ ಸ್ಕ್ವೇರ್

Question 65 1 Marks

What is the square root of 0.017?

A

0.001

B

0.13

C

0.00001

D

0.000001

Question 66 1 Marks

What is the definition of ratio?

A

Relation of two quantities of the same kind

B

Relation of two quantities of the different kind

C

Equality between two ratios

D

Inequality between two ratios

Question 67 1 Marks

What is the ratio of 4 kg to 800 grams?

A

05:01

B

04:08

C

08:04

D

02:04

Question 68 1 Marks

What percentage of 80 is 20?

A

0.8

B

0.4

C

0.25

D

0.2

Question 69 1 Marks

How much is 8% of 40 kg?

A

2.2 kg

B

3.2 kg

C

4.2 kg

D

5.2 kg

Question 70 1 Marks

Convert 52% into fraction?

A

(9/25)

B

(11/25)

C

(13/25)

D

(17/25)

Question 71 1 Marks

Convert 0.456 decimal fraction into percentage?

A

0.456

B

0.0456

C

45.6

D

0.000456

Question 72 1 Marks

What is the x value for x<sup>2</sup> + 62 = 126?

A

4

B

6

C

8

D

10

Question 73 1 Marks

What is the square root of decimal number 550.37?

A

21.26

B

22.26

C

22.46

D

23.46

Question 74 1 Marks

What is the length L2, if total length (L) is 2.75 metre and L1:L2 = 2:3?

A

1.1 metre

B

1.25 metre

C

1.65 metre

D

1.75 metre

Question 75 1 Marks

How many days a mechanic takes to assemble 64 machines if he assembles 8 machines in 3 days?

A

20 days

B

22 days

C

24 days

D

26 days

Question 76 1 Marks

What will be the rpm of smaller gear if a 180 mm dia meshes with 60 mm dia gear and the bigger gear makes 60 rpm?

A

120 rpm

B

140 rpm

C

160 rpm

D

180 rpm

Question 77 1 Marks

What is the percentage of copper if the casting weight of copper 42.3 kg and tin weight 2.7 kg?

A

Cu 92%

B

Cu 94%

C

Cu 96%

D

Cu 98%

Question 78 1 Marks

A motor cycle tyre is sold for Rs 300/- what is the purchase price if 25% profit is added to it.

A

Rs 200

B

Rs 220

C

Rs 240

D

Rs 260

Question 79 1 Marks

What is the decimal fraction of conversion of 18.5%?

A

0.185

B

0.175

C

0.165

D

0.195

Question 80 1 Marks

Which part connects the petrol engine
inlet manifold?

A

Air filter

B

Injector

C

Carburetor

D

Fuel pump

Question 81 1 Marks

What is the material of inlet manifold?

A

Brass

B

Bronze

C

Stainless steel

D

Aluminium alloy

Question 82 1 Marks

Which component is related to exhaust
system?

A

Muffler

B

Air filter

C

Carburetor

D

Injection pump

Question 83 1 Marks

Which is related to pneumatic system?

A

Steam

B

Electric

C

Compressed air

D

Pressurized water

Question 84 1 Marks

Where is the turbocharger mounted?

A

Air filter

B

Inlet manifold

C

Cylinder head

D

Exhaust manifold

Question 85 1 Marks

What is the material of exhaust manifold?

A

Brass

B

Bronze

C

Cast iron

D

Steel alloy

Question 86 1 Marks

Which type of muffler produces anti noise
without restricting exhaust flow?

A

Baffle type

B

Electronic type

C

Reverse flow type

D

Straight through type

Question 87 1 Marks

Which type of muffler is fitted with
sensors and microphone ?

A

Electronic type

B

Resonance type

C

Reverse flow type

D

Straight through type

Question 88 1 Marks

Which process is taken place in catalytic convertor?

A

Thermal

B

Physical

C

Chemical

D

Biological

Question 89 1 Marks

What is the purpose of the turbo charger?

A

Save power

B

Scavenging

C

Filter the exhaust gas

D

Pump more air into the cylinder

Question 90 1 Marks

How does a turbocharger get drive?

A

By belt

B

By gear

C

By inlet gas

D

By exhaust gas

Question 91 1 Marks

Which one of the following acts as a flame arrester during engine back fire?

A

Muffler

B

Oil filter

C

Air filter

D

Fuel filter

Question 92 1 Marks

Which type of filter element is fitted in dry type air cleaner?

A

Cloth

B

Paper

C

Strainer

D

Wire mesh

Question 93 1 Marks

What is the purpose of the muffler in the exhaust system?

A

To reduce the heat

B

To reduce the noise

C

To reduce the vibration

D

To filter the exhaust gases

Question 94 1 Marks

Where the exhaust system muffler is connected?

A

Between exhaust pipe and tail pipe

B

Between tail pipe and exhaust manifold

C

Between engine head and exhaust manifold

D

Between exhaust pipe and exhaust manifold

Question 95 1 Marks

Where the catalytic converters are used?

A

Fuel system

B

Inlet system

C

Exhaust system

D

Lubrication system

Question 96 1 Marks

What is the purpose of catalytic converter?

A

Control the noise

B

Control the emission

C

Control the temperature

D

Control the fuel consumption

Question 97 1 Marks

Where the catalytic converter is fitted?

A

Between muffler and tail pipe

B

Between exhaust pipe and muffler

C

Between tail pipe and resonator pipe

D

Between engine head and exhaust manifold

Question 98 1 Marks

Which are the materials commonly used in the catalytic converter?

A

Zinc and molybdenum

B

Palladium and platinum

C

Asbestos and ceramics

D

Chromium and vanadium

Question 99 1 Marks

What is the reason to decrease the volumetric efficiency in exhaust system?

A

Low noise

B

High temperature

C

Low temperature

D

Excessive back pressure

Question 100 1 Marks

Which metal in the fuel is to be avoided while fitting catalytic convertor?

A

Tin

B

Lead

C

Chromium

D

Phosphorus

Which one is the properties of lubricant

Which part drives the oil pump?

Which part is lubricated by splash lubrication system?

How oil deliver from the crank shaft main bearings to connecting rod bearings?

What is the purpose of a radiator pressure cap?

What is the purpose of water pump in cooling system?

Which part is used to pump the water in water pump?

What is the effect if thermostat valve is struck?

Where heat dissipation take place in cooling system?

Which type of pump is used in water cooling system?

How many valves are used in radiator cap?

Which part allows to flow water from upper tank to lower tank of the radiator?

What is the purpose of the radiator in the cooling system?

What is the purpose of metal fins in air cooling system?

Where the metal fins are provided in the air cooled engine?

Which types of cooling system the rate of cooling is very low?

How the water pump get drive in pump circulation cooling system?

Which mixture is used in radiator reverse flushing cleaning?

When the thermostat valve open in engine?

What is the material used to produce crank shaft?

What is the material of piston pins?

What is the name the portion below the piston boss?

What type of bearing fitted in the connecting rod big end?

Which part connect the piston with connecting rod?

Which part is connect the piston with crank pin?

Which tool used to remove the crank shaft pully?

Which tool is used to measure the diameter of the crank shaft main journal?

What is the material for cam shaft?

Which tool is required to remove the valves?

Which instrument is used to check the vacuum of the cylinder?

Which measuring instrument used to check the fly wheel face out?

Which is the most preferred use of taper roller bearings?

What is the property of a bearing helps to with stand metal to metal contact?

Which is the most preferred use of roller bearings?

Which is connected with pison through piston pin?

Which is the key element in converting reciprocating motion in to rotary motion?

Which is transferring energy for the piston to crankshaft?

Which is the load taken by the roller bearing?

1). Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

Identify the name of the triangle? | ತ್ರಿಕೋನದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

Identify the correct aligned system dimension? | ಸರಿಯಾದ ಜೋಡಿಸಲಾದ ಸಿಸ್ಟಮ್ ಆಯಾಮವನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

Which single stroke inclined letter ʹAʹ is correct as per IS standard? | IS ಮಾನದಂಡದ ಪ್ರಕಾರ ಯಾವ ಏಕ ಸ್ಟ್ರೋಕ್ ಇಳಿಜಾರಿನ ಅಕ್ಷರ ʹAʹ ಸರಿಯಾಗಿದೆ?

Which arrow head is correct as per standard? | ಮಾನದಂಡದ ಪ್ರಕಾರ ಯಾವ ಬಾಣದ ಹೆಡ್ ಸರಿಯಾಗಿದೆ?

Which dimension correctly marked in the circle as per standard? | ಮಾನದಂಡದ ಪ್ರಕಾರ ವೃತ್ತದಲ್ಲಿ ಯಾವ ಆಯಾಮವನ್ನು ಸರಿಯಾಗಿ ಗುರುತಿಸಲಾಗಿದೆ?

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

Identify the name of instrument? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Which drawing dimension is correct as per IS standard? | IS ಮಾನದಂಡದ ಪ್ರಕಾರ ಯಾವ ರೇಖಾಚಿತ್ರದ ಆಯಾಮವು ಸರಿಯಾಗಿದೆ?

Identify the line ʹbʹ? | ʹbʹ ಸಾಲನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the name of prism? | ಪ್ರಿಸ್ಮ್ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the name of tool? | ಉಪಕರಣದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

What is the trimmed size of A4 sheet? | A4 ಹಾಳೆಯ ಟ್ರಿಮ್ ಮಾಡಿದ ಗಾತ್ರ ಎಷ್ಟು?

Identify the conventional symbol of material? | ವಸ್ತುವಿನ ಕನ್ವೇಷನಲ್ ಚಿಹ್ನೆಯನ್ನು ಗುರುತಿಸಿ?

Which drawing dimension is correct as per standard drawing practice? | ಸ್ಟ್ಯಾಂಡರ್ಡ್ ಡ್ರಾಯಿಂಗ್ ಅಭ್ಯಾಸದ ಪ್ರಕಾರ ಯಾವ ಡ್ರಾಯಿಂಗ್ ಆಯಾಮ ಸರಿಯಾಗಿದೆ?

Which title block position is correct as standard practice? | ಪ್ರಮಾಣಿತ ಅಭ್ಯಾಸದಂತೆ ಯಾವ ಶೀರ್ಷಿಕೆ ಬ್ಲಾಕ್ ಸ್ಥಾನವು ಸರಿಯಾಗಿದೆ?

Identify the name of prism? | ಪ್ರಿಸ್ಮ್ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Compass used to draw for___. | ಕಂಪಾಸ್ ಅನ್ನು ___ ಗೆ ಸೆಳೆಯಲು ಬಳಸಲಾಗುತ್ತದೆ.

Identify the name of set square? | ಸೆಟ್ ಚೌಕದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

Identify the name of set square? | ಸೆಟ್ ಚೌಕದ ಹೆಸರನ್ನು ಗುರುತಿಸುವುದೇ?

What is the square root of 0.017?

What is the definition of ratio?

What is the ratio of 4 kg to 800 grams?

What percentage of 80 is 20?

How much is 8% of 40 kg?

Convert 52% into fraction?

Convert 0.456 decimal fraction into percentage?

What is the x value for x<sup>2</sup> + 62 = 126?

What is the square root of decimal number 550.37?

What is the length L2, if total length (L) is 2.75 metre and L1:L2 = 2:3?

How many days a mechanic takes to assemble 64 machines if he assembles 8 machines in 3 days?

What will be the rpm of smaller gear if a 180 mm dia meshes with 60 mm dia gear and the bigger gear makes 60 rpm?

What is the percentage of copper if the casting weight of copper 42.3 kg and tin weight 2.7 kg?

A motor cycle tyre is sold for Rs 300/- what is the purchase price if 25% profit is added to it.

What is the decimal fraction of conversion of 18.5%?

Compass used to draw for_. | ಕಂಪಾಸ್ ಅನ್ನು _ ಗೆ ಸೆಳೆಯಲು ಬಳಸಲಾಗುತ್ತದೆ.

Which part connects the petrol engine
inlet manifold?

Which component is related to exhaust
system?

Which type of muffler produces anti noise
without restricting exhaust flow?

Which type of muffler is fitted with
sensors and microphone ?