Which one of the following code used to switch off the coolant pump?

What is the centre of gravity of a sphere?

Which state of equilibrium's example is, A cone resting on its base?

What force will be required to punch a hole of 10 mm dia in a 1 mm thick plate, if the allowable shear stress is 50N/mm²? (Pi = 22/7)

Which is the suitable nitriding process for all alloyed and unalloyed steels?

What is the other term of pocket reference in engineering works?

How the local action defect is prevented in voltaic cell? | ವೋಲ್ಟಾಯಿಕ್ ಸೆಲ್‌ನಲ್ಲಿ ಸ್ಥಳೀಯ ಕ್ರಿಯೆಯ ದೋಷವನ್ನು ಹೇಗೆ ತಡೆಯಲಾಗುತ್ತದೆ?

What is the purpose of tempering a steel?

What is the minimum permissible area of conductor (U/G cable) for three and half cores cable?

What is the use of the voltage dependent resistor? | ವೋಲ್ಟೇಜ್ ಅವಲಂಬಿತ ರೆಸಿಸ್ಟರ್‌ನ ಬಳಕೆ ಏನು?

What is the total construction cost of a house construction area of 3000 sq.ft. (cost of construction Rs.2000/- per sq.ft including material and labour)?

Why most of the semi conductor devices are made by silicon compared to germanium? | ಜರ್ಮೇನಿಯಮ್‌ಗೆ ಹೋಲಿಸಿದರೆ ಹೆಚ್ಚಿನ ಅರೆವಾಹಕ ಸಾಧನಗಳನ್ನು ಸಿಲಿಕಾನ್‌ನಿಂದ ಏಕೆ ತಯಾರಿಸಲಾಗುತ್ತದೆ?

Which mode the program will be executed continuously one block after another block?

What is the unit of electric charge? | ವಿದ್ಯುದಾವೇಶದ ಘಟಕ ಎಂದರೇನು?

Which state of equilibrium's example is A cone resting on its tip?

What is the youngs modulus if a wire of 2m long, 0.8 mm2 in cross section increases its length by 1.6 mm on suspension of 8 kg weight from it?

Which mode, the cutting tool returns back to its home position?

What is the reason for more barrier voltage in silicon diode than germanium diode? | ಸಿಲಿಕಾನ್ ಡಯೋಡ್‌ನಲ್ಲಿ ಜರ್ಮೇನಿಯಮ್ ಡಯೋಡ್‌ಗಿಂತ ಹೆಚ್ಚು ತಡೆಗೋಡೆ ವೋಲ್ಟೇಜ್‌ಗೆ ಕಾರಣವೇನು?

What percentage of water absorbed by a good building stone?

What is the ratio of shear stress to shear strain?

Which instrument is used to measure the specific gravity of electrolyte in lead acid battery? | ಲೀಡ್ ಆಯ್ಸಿಡ್ ಬ್ಯಾಟರಿಯ ನಿರ್ದಿಷ್ಟ ಗುರುತ್ವ ವಿದ್ಯುದ್ವಿಚ್ಛೇದ್ಯವನ್ನು ಅಳೆಯಲು ಯಾವ ಉಪಕರಣವನ್ನು ಬಳಸಲಾಗುತ್ತದೆ?

Which process steel is heated in a carbonaceous atmosphere for the penetration of carbon?

Which hand book referred by machine engineer?

Which of the impurity in cast iron makes it hard and brittle?

What is the activity of code M06 based on FANUC CNC control system?

Which mode is used for five positioning (Micron level) of the axis movement?

What is the unit of strain?

What is the term used for maximum stress attained by a material before rupture?

What is a hand book?

What is the ratio between the change in dimension to its original dimension of the substance?

What is the safe stress if the ultimate stress of a material is 35 kg/mm² and factor of safety is 5?

What is the name of the resistor as shown in the figure? | ಚಿತ್ರದಲ್ಲಿ ತೋರಿಸಿರುವಂತೆ ರೆಸಿಸ್ಟರ್‌ನ ಹೆಸರೇನು?

What is the total cost of painting of a class room including ceiling, if the size of length is 6m, breadth is 5m and height is 4m. (Painting + labour cost Rs.150/- per sq.m)

What is the maximum percentage of stretch of its original length is allowable for elastic materials?

How the positive plate changes, after the complete charging of lead acid battery? | ಲೀಡ್ ಆಸಿಡ್ ಬ್ಯಾಟರಿಯ ಸಂಪೂರ್ಣ ಚಾರ್ಜಿಂಗ್ ನಂತರ ಧನಾತ್ಮಕ ಪ್ಲೇಟ್ ಹೇಗೆ ಬದಲಾಗುತ್ತದೆ?

Which G-code is suitable for thread cutting?

Which symbol is used to express change in length?

What is the name of the resistor as shown in the figure? | ಚಿತ್ರದಲ್ಲಿ ತೋರಿಸಿರುವಂತೆ ರೆಸಿಸ್ಟರ್‌ನ ಹೆಸರೇನು?

What is the youngs modulus if a wire of 2m long, 0.8 mm2 in cross section increases its length by 1.6 mm on suspension of 8 kg weight from it?

Which standard schedule of rates to be considered for estimation?

What percentage of water absorbed by a good building stone?

What is a total cost?

What is the use of CNC code of M05 to develop the command?

What is the ratio of shear stress to shear strain?

Which M code is used to activate coolant pump in CNC machine?

What is the unit of strain?

How the capacity of the batteries are specified? | ಬ್ಯಾಟರಿಗಳ ಸಾಮರ್ಥ್ಯವನ್ನು ಹೇಗೆ ಸೂಚಿಸಲಾಗಿದೆ?

Which standard schedule of rates to be considered for estimation?

What is the other term used for reference table?

What force will be required to punch a hole of 10 mm dia in a 1 mm thick plate, if the allowable shear stress is 50N/mm²? (Pi = 22/7)