What is the special benefit of using a fixture?

Which is a non-metallic tool material?

Where the follower is fixed to produce from turning?

Find out the R.P.M of spindle for a 50mm bar (D) and cutting speed is 25m/min.

What is the advantage of jig?

What factor is important in free hand form turning?

Which cutting tools have highest cutting efficiency?

What will happen to the tool life if the spindle is running higher speed?

What is the effect, if the cutting speed is more than the recommanded?

How much percentage of cutting speed could be increased by using super HSS tools?

Which type of jig is used to hold thin and soft parts?

Which type of jig is used for large awkward shaped piece part is to drilled in many directions?

What defect may occur during grinding a form tool cutting edge?

What is the name of gauge used to check the radius

Which gauge is to be selected for checking the corner radius of the job?

How the cutting speed is expressed?

What does the letter 's' stands in the equation d =Y-2(s+r) in taper measurement?

Which type of jig locates the piece part from its face?

Which is the device that can hold, locate and guide the tool?

What is the recommended cutting speed for turning mild steel using H.S.S tool?

How many precision rollers required for measuring angle of tapered component?

Calculate the spindle speed to turn a 40mm dia M.S rod using a cemented carbide tool it cutting speed is 92mm/min?

What is the recommended feed rate for turning cast iron (grey) using H.S.S tool?

Calculate the length of metal passing by cutting tool in one revolution if the diameter of work is 75mm and cutting speed is 120m/min.

What is the tool life index of cemented carbide tool for turning high carbon high chromium die steel?

What will happen to the tool life if the spindle is running higher speed?

Which gauge is used to check the radius formed at the steps of component?

Which material is used to make radius gauge?

Which type of tool is suitable to produce form surface in mass production activities?

What does the letter Y stands in the formula d = Y ? 2 (s+r) in taper measurement?

Which one is chief constituent of ferrous tool material?

How many precision rollers required for measuring angle of tapered component?

What is the recommended cutting speed for aluminium using H.S.S tool?

Which is the device that can hold, locate and guide the tool?

What is the value of tool life index for a cemented carbide tip to machine cast iron component?

What is the term the distance moved by the tool along the work for each revolution?

Which gauge is used to check the radius formed at the steps of component?

Which is a non-metallic tool material?

What is the name of the fit shown in the figure? | ಚಿತ್ರದಲ್ಲಿ ತೋರಿಸಿರುವ ಫಿಟ್‌ನ ಹೆಸರೇನು?

What is the name of the part marked as ‘X’ shown in the figure? | ಚಿತ್ರದಲ್ಲಿ ತೋರಿಸಿರುವ ʹXʹ ಎಂದು ಗುರುತಿಸಲಾದ ಭಾಗದ ಹೆಸರೇನು?

What is the advantage of cutting fluid in turning operation? | ಟರ್ನಿಂಗ್ ಕಾರ್ಯಾಚರಣೆಯಲ್ಲಿ ಕಟಿಂಗ್ ಫ್ಲೂಯಿಡ್ ನ ಪ್ರಯೋಜನವೇನು?

Which process refers to the finishing of drilled hole? | ಯಾವ ಪ್ರಕ್ರಿಯೆಯು ಡ್ರಿಲ್ಲ್ಡ್ ಹೋಲ್ ಫಿನಿಶಿಂಗ್ ಮಾಡಲು ಸೂಚಿಸುತ್ತದೆ?

What is the least count of the metric vernier micrometer? | ವಾನಿಯರ್ ಮೈಕ್ರೋಮೀಟರ್ನ ಕನಿಷ್ಠ ಎಣಿಕೆ (ಲೀಸ್ಟ್ ಕೌಂಟ್) ಏನು?

What is the accuracy of a metric outside micrometer? | ಮೆಟ್ರಿಕ್ ಔಟ್ ಸೈಡ್ ಮೈಕ್ರೊಮೀಟರ್‌ನ ಆಕ್ಯುರೆಸಿ ಏನು?

Which tool is used to remove high spots on all flat and curved surfaces? | ಎಲ್ಲಾ ಫ್ಲಾಟ್ ಮತ್ತು ಬಾಗಿದ ಮೇಲ್ಮೈಗಳಲ್ಲಿ (ಕರ್ವ್ಡ್ ಸರ್ಫೆಸ್) ಹೆಚ್ಚಿನ ಕಲೆಗಳನ್ನು ತೆಗೆದುಹಾಕಲು ಯಾವ ಸಾಧನವನ್ನು ಬಳಸಲಾಗುತ್ತದೆ?

What is the advantage of gauging of components? | ಕಾಂಪೊನೆಂಟ್ಗಳ ಅಳೆಯುವಿಕೆಯ ಪ್ರಯೋಜನವೇನು?

Which hammer is suitable for riveting? | ಯಾವ ಸುತ್ತಿಗೆ ರಿವೇಟಿಂಗಿಗೆ ಸೂಕ್ತವಾಗಿದೆ?

What is the reading accuracy of the steel rule? | ಸ್ಟೀಲ್ ರೂಲಿನ ರೀಡಿಂಗ್ ಆಕ್ಯುರೆಸಿ ಏನು?

Which process refers to the finishing of drilled hole? | ಯಾವ ಪ್ರಕ್ರಿಯೆಯು ಡ್ರಿಲ್ಲ್ಡ್ ಹೋಲ್ ಫಿನಿಶಿಂಗ್ ಮಾಡಲು ಸೂಚಿಸುತ್ತದೆ?

Which punch is used for witness marks? | ಅಳಿಸದ ಗುರುತುಗಳನ್ನು (ವಿಟ್ನೆಸ್ ಮಾರ್ಕ್ಸ್) ಪಂಚ್ ಮಾಡಲು ಯಾವ ಪಂಚ್ ಉಪಯೋಗಿಸಲಾಗುತ್ತದೆ?